Products

I would like to take a minute to thank everyone for your buisness,
and for all the great comments about my parts and fast shipping.


Contact me at

Heller1m@yahoo.com




Sleeve Hitch Adapter
As far as 3 point hitch adapters go, here is what I think is the bad boy on the block. It's made from 2-1/4" X 3/8" flat stock and weighs in at 14 lbs. it comes with everything you need to pin it on and go to work. You're gonna have a hard time bending this one.
Note: Shown with both styles of lift strap only one set is included, buyers choice, floating or down pressure style.
$122.75 plus $17.25 shipping including delivery conformation to anywhere in the lower 48





Floating Lift Straps

Three point hitch adapter "floating" style lift straps.
$15.00 a pair plus $5.00 shipping to anywhere in the lower 48.



Down Pressure Style Lift Straps

Three point hitch adapter "Down Pressure" style lift straps.
$15.00 a pair plus $5.00 shipping to anywhere in the lower 48.





Narrow Frame 3 point lift bar

$22.00 plus $12.82 shipping to anywhere in the lower 48




Narrow Frame 3 Point Lift Bar Bushing

$4.00 plus $3.80 shipping to anywhere in the lower 48




Wide and Narrow Frame 3 Pin Driver.

Turned to 6-1/4" diameter and 3/16" thick then threaded to accept 3, 3/8" grade 8 studs as pins and nutted on both sides to keep them tight. These drivers are about twice as tough as the factory 6" X 1/8" factory drivers. I can also make up 6 pin drivers as well.
$61.33 each plus 8.50 shipping to anywhere in the lower 48.





Core/No Core
Rebuilt Narrow Frame Clutch
New Stainless Steel 304 Alloy Drive Shaft, New (Stock Pressure) Spring, New Throw Out Bearing, New Teaser Spring, New Clutch Disk, New Washers and New Spiral Pins. The pressure plates were turned in my lathe and the release lever shows no signs of wear.

$175.00 *Exchange, plus $18.00 shipping to anywhere in the lower 48.

Core Charge $75.00





Aluminum Clutch Disk
After getting so many requests for 6 hole disks I decided to just make them all that way, a 6 hole disk will still fit 3 a pin driver.

Made from 1/4" 6061 alloy aluminum, these clutches are great for pulling or stock applications.


They are a full 1/4" thick and 6-1/4" in diameter, there is plenty of "meat" around the driver holes to help keep them from tearing out.

Aluminum clutches vary greatly from factory fiber clutches, there is no "middle ground" with these, they are either ON or OFF no slipping the clutch to pull up close. Recommended for tractors that pull heavy loads or mow in the "wide open". NOT recommended for use in tight spaces or for inexperienced operators.

$28.00 each plus $5.50 shipping to anywhere in the lower 48




Wide Frame Gear Drive Stainless Steel Drive Shafts.
Possibly the last drive shaft your tractor will ever need. Made from 304 alloy stainless steel, I expect the ones in my tractors to be in use LONG after I'm gone.

$30.00 each Plus $10.00 shipping to anywhere in the lower 48
Please specify with or without creeper gear.




Narrow Frame gear drive Stainless Steel Drive Shafts.
Same as the Wide Frame shafts except cut and drilled for Narrow Frame tractors.

$30.00 each Plus $10.00 shipping to anywhere in the lower 48





Core/No Core
REBUILT Wide Frame Style, Manual Front PTO.

This isn't some taken apart "cleaned up" and put back together PTO this one was rebuilt with a New Cub Cadet fiber disk, new springs, new center button and adjusted as per adjustment gauge. Comes with 6 new set screws, adjustment gauge, and instruction sheet.

$130.00 *EXCHANGE, plus $13.75 shipping including insurance to anywhere in the lower 48.

Core Charge $50.00





Manual Front PTO Set Screws

Set of 6 set screws for all Wide and Narrow Frame mechanical front PTO's

$7.50 plus $4.30 shipping to anywhere in the lower 48.





Brand New,

Front Blade Skid Shoes.


These are different from any others you've ever seen, the steel on the shoe is a FULL 1/2" thick and 2-7/8" in diameter, the bolts on these are regulation grade 8 fully threaded 2-1/4" bolts, not the cheap old full thread carrage bolts, found on other replacement shoes. These shoes are built to LAST. Compare price and and quality. Hardware included.

$40.00 a pair. $6.50 shipping to anywhere in the lower 48.




Steering Upgrade

Here is everything needed to upgrade the gear box on your steering column.

Included in this package are, the "Nice 605" bearing, two .032 thrust washers and 5/8" fine thread jamb style lock nut.

$10.00 plus $4.30 shipping to anywhere in the lower 48.




Steering Gear Cam Follower.

Made from grade 8 bolt stock this cam follower will fit all IH Cub Cadets with approximately a 1 1/2" X 1/2" 20 tpi cam follower.

$14.00 each plus $4.30 shipping to anywhere in the lower 48.



CUB CADET ORIGINAL, 70/100, 71, 72, 73 and some Loboy
REPRODUCTION TAIL LIGHT AND BRACKET


These tail lights are as close to factory as I've ever seen, nearly the same thickness and diameter, same bolt pattern and all metal construction, almost identical to the originals.

Tail light comes in black finish, bracket is painted only to prevent rust. Mounting hardware included.

Special introductory price $25.00 plus $6.50 shipping to anywhere in the lower 48.



REBUILT MOWER DECK CENTER SPINDLE and PULLEY
Temporarily Out Of Stock


Fits most of the IH Cub Cadet mower decks with the cast iron and wooden roller middle section, along with other decks. These spindles are disassembled, soaked in a parts washer, cleaned and wire brushed, new bearings, races and seals are installed. The pulleys and hardware are media blasted, then all parts are repainted and reassembled. Some hardware may be replaced as necessary.

Pulleys measure about 6-1/4" and 7-1/8" in diameter and show no signs of ever being bent.

Please understand; these were used spindles and may show some signs of prior use.

Spindles MUST be greased before use.

$65.00 each plus $10.25 shipping including delivery conformation to anywhere in the lower 48.

If you have any questions about these spindles (or any of my other parts) don't hesitate to email me.



Rebuilt Mower Deck Outer Spindle and Pulley
Temporarily Out Of Stock


Fits most of the IH Cub Cadet mower decks with the cast iron and wooden roller middle section along with other decks. These spindles are disassembled, soaked in a parts washer, cleaned and wire brushed, new bearings, races, and seals are installed. The pulleys and hardware are media blasted, then all parts are repainted and reassembled. Some hardware may be replaced as necessary.

Pulleys measure about 3" in diameter in diameter and show no signs orf ever being bent.

Please understand: these were used spindles and may show some signs of prior use.

Spindles MUST be greased before use.

$65.00 each plus $8.25 including delivery conformation to anywhere in the lower 48.

If you have questions about these spindles (or any of my other parts) don't hesitate to email me.




Air/Liquid Adapter Kit
Used to fill tires with liquid ballast.
Comes with fittings for different sized valve stems
$14.00 plus $4.80 shipping to anywhere in the lower 48






Heller1m@yahoo.com

I ALWAYS COMBINE SHIPPING WHENEVER POSSIBLE TO HELP KEEP YOUR COST DOWN!

*Exchange Policy: Core MUST be a rebuildable part or core charge will apply, sorry no exceptions.